If your PC keeps restarting and showing the “Preparing Automatic Repair” or “Diagnosing your PC” screen, you are likely stuck in a frustrating “boot loop.” This feature, known as “Automatic Repair”, is built into both “Windows 11” and “Windows 10” to detect and fix startup problems. While it can be helpful, it sometimes fails repeatedly and traps your system in a loop where it never reaches the desktop.
In such cases, disabling “Automatic Repair” can help you regain control of your system.
Let’s learn the way that can help you disable it easily!
When Should You Disable Automatic (Boot Loop) Repair?
You should consider disabling“Automatic Repair” when your system is stuck in a continuous restart cycle and never progresses beyond the repair screen. If you have already attempted basic solutions like restarting your PC, disconnecting external devices, or accessing Safe Mode, but nothing works, disabling this feature becomes a practical step.
Another scenario is when “Automatic Repair” repeatedly fails to fix the issue. Instead of helping, it prevents you from accessing advanced troubleshooting tools. In such cases, disabling it allows you to manually diagnose the problem using command-line tools or system restore options.
You might also disable it temporarily if you are performing advanced troubleshooting or repairs, especially when following technical instructions that require uninterrupted boot attempts.
However, if your system occasionally boots normally or the issue is minor, it is better to leave “Automatic Repair” enabled. Disabling it removes a safety net, so it should only be done when necessary.
How to Disable Automatic (Boot Loop) Repair in Windows 11 or 10?
To disable “Automatic Repair” in Windows 11 or 10, access the “Advanced Startup Options,” open the “Command Prompt,” and run the command bcdedit /set recoveryenabled no. Restart your computer to apply the changes. This will stop Windows from automatically entering repair mode during boot failures.
Step 1: Access the Advanced Startup Environment
First of all, enter the “Advanced Startup Options” menu.
If your PC is stuck in a loop, you can force it into this mode by interrupting the boot process. Turn on your computer and as soon as you see the Windows logo, press and hold the power button to force a shutdown. Repeat this process two or three times. On the next startup, Windows will automatically load the “Recovery Environment.”
If your system still responds partially, you can access this menu by holding the Shift key and clicking Restart from the login screen. This method is cleaner and safer.
Once you reach the blue recovery screen, you are in the correct place to proceed.
After entering the recovery environment, you will see several options. Select “Troubleshoot” to access advanced tools.
Inside the Troubleshoot section, click on “Advanced Options.” This section contains utilities like System Restore, Startup Settings, and Command Prompt. These tools are essential for diagnosing and fixing deeper system issues.
Understanding this step is important because it ensures you are not making changes randomly. You are entering a controlled environment designed specifically for system repair and configuration.
Step 3: Open Command Prompt
Within the “Advanced Options” menu, locate and select “Command Prompt.”
This tool allows you to interact directly with the system using commands. While it may look intimidating, you only need to enter a single command to disable “Automatic Repair.”
When you open Command Prompt, your system may ask for your administrator password. Enter it to proceed. Once the command window appears, you are ready to make the required change.
Step 4: Enter the Command to Disable Automatic Repair
In the Command Prompt window, type the following command carefully:
“bcdedit /set recoveryenabled no”
After typing the command, press Enter. If the command is successful, you will see a confirmation message stating that the operation completed successfully.
This command modifies the “Boot Configuration Data”, which controls how your system starts. By setting recoveryenabled to “no,” you are instructing Windows not to trigger the automatic repair process during boot failures.
It is important to type the command exactly as shown. Even a small typo can result in an error.
Step 5: Restart Your Computer
After running the command, close the Command Prompt window and select the option to restart your computer.
When your system reboots, it will no longer automatically enter the repair loop. Instead, it will attempt to boot normally, even if there are underlying issues.
This allows you to observe what happens during startup and apply further troubleshooting methods if needed.
Step 6: Perform Manual Troubleshooting if Needed
Once “Automatic Repair” is disabled, your system may either boot successfully or display an error message. If it still fails to boot, you now have the opportunity to diagnose the issue manually.
You can return to the recovery environment and use tools like “System Restore”, “Startup Settings”, or additional command-line utilities. These options give you more control compared to being stuck in a loop.
Disabling automatic repair is not the final solution, but a way to break the cycle and regain access to your system.
Faqs
What does Automatic Repair actually do in Windows?
Automatic Repair is a built-in feature that detects and fixes startup problems such as corrupted system files or boot configuration errors. It runs automatically when Windows fails to start properly multiple times.
Is it safe to disable “Automatic Repair”?
Yes, it is safe if done correctly and for the right reasons. However, you should only disable it when you are stuck in a loop or need to perform manual troubleshooting.
Can I enable “Automatic Repair” again later?
Yes, you can re-enable it by using the Command Prompt and entering the command “bcdedit /set recoveryenabled yes.” This restores the default behavior.
Will disabling it fix my boot issue?
Not directly. It stops the loop but does not repair the underlying problem. You will still need to diagnose and fix the root cause.
What if the command does not work?
If the command fails, double-check the syntax. If it still does not work, there may be deeper issues with your system configuration or permissions.
Summary
Disabling “Automatic Repair” in Windows 11 or 10 is a practical solution when your system is stuck in a continuous boot loop. While the feature is designed to help, it can sometimes prevent you from accessing your system altogether.
By entering the “Advanced Startup Options”, opening the “Command Prompt”, and running the correct command, you can stop the loop and regain control. This process allows you to move forward with manual troubleshooting and resolve the actual issue.